 |
Airgun Designs Europe - EMAG And WARP FEED EUROPEAN LAUNCH
| Airgun
Designs Europe has Warp Interfaces available for the Angel (LCD
& Non-LCD), Shocker, Impulse, BM2K & most mechanical markers.
We
have been installing limited numbers of these interfaces and
testing them since early January.
The
kit contains all the necessary fittings, and are fairly simple
to install yourself, or you can send your marker in, and have
your interface factory fitted.
The
interface is also now available for most mechanical guns, like
the RT, Automag, Autococker etc. But interfaces for mechanical
guns are factory fit only, as they require some small mods to
the frame.
Below
are the installation instructions for the above electric markers.
Call
or e-mail for more info
|
| BM2K
WARP INTERFACE INSTALLATION INSTRUCTIONS |
|
| WARNING
!!!!- DISCONNECT YOUR MARKER'S BATTERY, |
| AND
ALL POWER, BEFORE COMMENCING INSTALLATION. |
|
| 1 |
Place the Red wire of the
Warp Inteface lead into one of the small green & clear snap
connectors, ensuring that this wire goes into the hole that
is blocked one end.
|
| 2 |
Next
identify the 5 volt wire on your BM2K circuit board.
This is coloured yellow on our diagram, but it is the second
wire from the left.(See Diagram Below) |
| 3 |
Place
the BM2K 5 volt wire into the the snap connector, by sliding it
into the open-sided hole of the connector. |
| 4 |
Ensuring
that both wires are in the correct position inside the connector,
push the green button of the connector firmly.
This will splice into the two wires, forming a connection,
and release a sealing solution inside. |
| 5 |
Strip
approx 1/4" of the insulation off the end of the Black wire,
and place through the small piece of Black heat shrink tube (inside
the package). |
| 6. |
Place
the stripped end of the Black wire through the Earth Mounting
Ring (inside the package) and squeeze tight with a set of pliers |
| 7 |
Slide
the Black Heat shrink tube over the connection, and heat with
a very low flame, taking care not to overheat, until the Heat
shrink has shrunk evenly over the wire. |
| 8 |
Now
take a suitable allen key, and unscrew the Hex Earth Mount Screw
on the circuit board (See Diagram Below) |
| 9 |
Place
the Earth Mounting Ring onto the Hex Earth Mount Screw, and screw
it back onto the circuit board, ensuring that it makes a suitable
contact. |
| 10 |
Ensure
that the snap connector, and the wires are safely inside the grip
frame, then carefully replace the grips. |
| 11 |
Lastly,
take the cover off the warp circuit board, and refer to your warp
Feed instructions. |
|
You
will see a diagram of the Jumper settings for the warp.
Refer to the diagram for the 3 position jumper, and ensure that
only one connector is installed on the Negative jumper setting,
as your BM2K will now operate directly from the Warp Feed Interface. |
 |
 |
| IF
YOU HAVE ANY QUESTIONS, OR ARE UNSURE ABOUT THE INSTALLATION |
| PROCEDURE,
PLEASE TELEPHONE OUR TECH SUPPORT LINE ON : +44 (0)1206 243450 |
|
| YOU ARE NOW
READY TO RE-CONNECT THE BATTERY, AND TEST THE WARP. |
| |
| ANGEL
LCD WARP INTERFACE INSTALLATION INSTRUCTIONS |
WARNING
!!!!- DISCONNECT YOUR MARKER'S BATTERY,
AND ALL POWER, BEFORE COMMENCING INSTALLATION. |
| 1 |
Place the Red wire of the
Warp Inteface lead into one of the small green & clear snap
connectors, ensuring that this wire goes into the hole that is
blocked one end. |
| 2 |
Next identify the 5 volt
wire on your Angel LCD circuit board. This is the wire on the
right, protruding from the top of the LCD display.
It is coloured Red on our diagram, but in some instances,
the wire may be coloured Black. (See Diagram Below) |
| 3 |
Place the Angel LCD 5 volt
wire into the the same snap connector, by sliding it into the
open-sided hole of the connector. |
| 4 |
Ensuring that both wires
are in the correct position inside the connector, push the green
button of the connector firmly.
This will splice into the two wires, forming a connection,
and release a sealing solution inside. |
| 5 |
Place the Black wire of the
Warp Inteface lead into the second small green & clear snap
connector, ensuring that this wire goes into the hole that is
blocked one end. |
| 6 |
Next identify the Earth wire
on your Angel LCD circuit board.
This is the wire on the left, protruding from the top of
the LCD Display. It
is coloured Black on our diagram, but in some instances, the wire
may be coloured Red. (See
Diagram Below) |
| 7 |
Place the Black Angel LCD
Earth wire into the the same snap connector, by sliding it into
the open-sided hole of the connector. |
| 8 |
Ensuring that both wires
are in the correct position inside the connector, push the green
button of the connector firmly.
This will splice into the two wires, forming a connection,
and release a sealing solution inside. |
| 9 |
Ensure that both of the snap
connectors, and the wires are safely inside the grip frame, then
carefully replace the grips. |
| 10 |
Lastly, take the cover off
the warp circuit board, and refer to your warp Feed instructions. |
| |
You will see a diagram of
the Jumper settings for the warp. |
| |
Refer to the diagram for
the 3 position jumper, and ensure that only one connector is installed
on the Negative jumper setting, as your Angel LCD will now operate
directly from the Warp Feed Interface. |
| |
Please Note : If the Warp
does not operate correctly, you may need to move the Warp jumper
to the Positive jumper setting. |
|
 |
| IF
YOU HAVE ANY QUESTIONS, OR ARE UNSURE ABOUT THE INSTALLATION |
| PROCEDURE,
PLEASE TELEPHONE OUR TECH SUPPORT LINE ON : +44 (0)1206 243450 |
|
| YOU ARE NOW
READY TO RE-CONNECT THE BATTERY, AND TEST THE WARP. |
| NON-LCD
ANGEL WARP INTERFACE INSTALLATION INSTRUCTIONS |
|
| WARNING
!!!!- DISCONNECT YOUR MARKER'S BATTERY, |
| AND ALL POWER,
BEFORE COMMENCING INSTALLATION. |
|
| 1 |
Place
the Red wire of the Warp Inteface lead into one of the small green
& clear snap connectors, ensuring that this wire goes into
the hole that is blocked one end. |
| 2 |
Next
identify the 5 volt wire on your NON-LCD Angel circuit board.
This is the wire on the right labelled D5. It is coloured Black
on our diagram, but in some instances, the wire may be another
colour (See Diagram Below) |
| 3 |
Place
the NON-LCD Angel 5 volt wire into the the same snap connector,
by sliding it into the open-sided hole of the connector. |
| 4 |
Ensuring
that both wires are in the correct position inside the connector,
push the green button of the connector firmly.
This will splice into the two wires, forming a connection,
and release a sealing solution inside. |
| 5 |
Place
the Black wire of the Warp Inteface lead into the second small
green & clear snap connector, ensuring that this wire goes
into the hole that is blocked one end. |
| 6 |
Next
identify the Earth wire on your NON-LCD Angel circuit board.
This is the wire on the left, labelled D6. It is coloured
Black on our diagram, but in some instances, the wire may be another
colour. (See Diagram Below) |
| 7 |
Place
the Black NON-LCD Angel Earth wire into the the same snap connector,
by sliding it into the open-sided hole of the connector. |
| 8 |
Ensuring
that both wires are in the correct position inside the connector,
push the green button of the connector firmly.
This will splice into the two wires, forming a connection,
and release a sealing solution inside. |
| 9 |
Ensure
that both of the snap connectors, and the wires are safely inside
the grip frame, then carefully replace the grips. |
| 10 |
Lastly,
take the cover off the warp circuit board, and refer to your warp
Feed instructions. |
|
You
will see a diagram of the Jumper settings for the warp. |
|
Refer
to the diagram for the 3 position jumper, and ensure that only
one connector is installed on the Negative jumper setting, as
your NON-LCD Angel will now operate directly from the Warp Feed
Interface. |
|
Please
Note : If the Warp does not operate correctly, you may need to
move the Warp jumper to the |
|
Positive
jumper setting. |
 |
 |
IF
YOU HAVE ANY QUESTIONS, OR ARE UNSURE ABOUT THE INSTALLATION
PROCEDURE, PLEASE TELEPHONE OUR TECH SUPPORT LINE ON : +44 (0)1206
243450
YOU ARE NOW READY TO RE-CONNECT THE BATTERY, AND TEST THE WARP.
IMPULSE / SHOCKER
WARP INTERFACE INSTALLATION INSTRUCTIONS
WARNING
!!!!- DISCONNECT YOUR MARKER'S BATTERY,AND ALL POWER, BEFORE COMMENCING
INSTALLATION. |
| 1 |
Open the circuit board housing
on your Impulse / Shocker. |
| 2 |
Feed the Warp Interface
lead up through the grip frame, so that it protrudes through next
to the circuit board. |
| 3 |
Unplug the small
white Solenoid plug from it's housing on the Circuit board. (See
Diagram below) Please
note that the Shocker has 2 solenoids, ensure that the Warp interface
is connected to the Fire Solenoid. |
| 4 |
Place
the Red wire of the Warp Interface lead into one of the small
green & clear snap connectors, ensuring that
this wire goes into the hole that is blocked one end. |
| 5 |
Next identify the
5 volt wire on your Impulse / Shocker circuit board.
This is also coloured Red on our diagram. It
is the Red Wire that is connected to the Solenoid plug.
(See Diagram Below) |
| 6 |
Place
the Red Impulse / Shocker
5 volt wire into the the same snap connector, by sliding
it into the open-sided hole of the connector. |
|
Ensuring
that both wires are in the correct position inside the connector,
push the green button of the connector firmly.
This will splice into the two wires, forming a connection,
and release a sealing solution inside. |
| 7 |
Place
the Black wire of the Warp Inteface lead into the second small
green & clear snap connector, ensuring that this wire goes
into the hole that is blocked one end. |
| 8 |
Next
identify the Earth wire on your Impulse / Shocker circuit board.
This is also coloured Black on our diagram.
It is the Black Wire that is connected to the Solenoid plug. |
|
(See Diagram Below) |
| 9 |
Place
the Black Impulse / Shocker Earth wire into the the same snap
connector, by sliding it into the open-sided hole of the connector. |
|
Ensuring
that both wires are in the correct position inside the connector,
push the green button of the connector firmly.
This will splice into the two wires, forming a connection,
and release a sealing solution inside. |
| 10 |
Ensure that both
of the snap connectors, and the wires are safely inside the grip
frame, then carefully re-assemble. |
| 11 |
Lastly, take the
cover off the warp circuit board, and refer to your warp Feed
instructions. |
|
You will see a
diagram of the Jumper settings for the warp. |
|
Refer
to the diagram for the 3 position jumper, and ensure that only
one connector is installed on the Negative jumper setting, as
your Impulse / Shocker will now operate directly from the Warp
Feed Interface. |
|
Please
Note : If the Warp does not operate correctly, you may need to
move the Warp jumper to the Positive jumper setting. |
|
| IF
YOU HAVE ANY QUESTIONS, OR ARE UNSURE ABOUT THE INSTALLATION |
| PROCEDURE,
PLEASE TELEPHONE OUR TECH SUPPORT LINE ON : +44 (0)1206
243450 |
|
| YOU ARE NOW
READY TO RE-CONNECT THE BATTERY, AND TEST THE WARP. |
|
| |
|
| |
